Level 1 · Settle and straighten · weeks 0–2
Patella mobilisations
Gently move your kneecap in each direction, so it slides freely and the knee stiffens less.
- 1 × 20
- No equipment
- Operated leg
General information, not medical advice. Follow your surgeon's and physio's plan. Read the disclaimer

Loading the 3D figure…
Key positions



Follow along
The highlighted step is the one playing. Tap a step to see it.
- Step 5: Keep it gentle: it should never hurt, and don't press on a wound or stitches
- Step 6: It may feel stuck at first; as the knee settles, the kneecap should move freely
How much
1 × 20
- Level 1 · Knee basics: 1 set of 20 reps. Slow glides each way. Straight after the heel prop.
Your physio may set a different dose. Theirs wins.
Before you start
This animation shows the exercise as the app describes it. It is general information, not medical advice. Follow your surgeon's and physiotherapist's instructions, and stop if the knee hurts.
On Level 1 the app adds a note after some surgeries:
- Meniscus repaired (stitched): Protocols for a repaired meniscus usually limit bending to 90° until week 6. Your surgeon may set a different limit for your repair. After a meniscus repair, protocols usually allow no weight on the leg for 4 weeks and partial weight to week 6. Your surgeon sets yours.
- Meniscus root or complex repair: Protocols for a root repair usually limit your bending to about 60° for the first 3 weeks. Your surgeon sets your exact limit. From week 3, protocols usually allow bending to about 90°, going further after week 6. Your surgeon sets your exact limit. After a root repair, protocols usually allow no weight on your leg for 6 weeks, then build to full weight by week 9.
- Revision surgery: After a revision, protocols use crutches and a brace for 2 to 6 weeks. Your surgeon sets how long, and how much weight you take. In the first 2 weeks after a revision, protocols usually limit your knee bend to about 90°.
- Cartilage microfracture: After microfracture, protocols often limit bending to 90° until week 6. Your surgeon may set a different limit, depending on where the cartilage was treated. Microfracture rehab depends on the size and location of the treated area. Where your surgeon's instructions differ from this plan, follow theirs. After microfracture, protocols usually allow no weight for up to 4 weeks, then about half your weight to week 6. Your surgeon sets yours.
- MCL injury, not operated: With an MCL injury, protocols usually keep your knee moving straight ahead, with no sideways steps or twisting, until about week 6.
- MCL repaired or reconstructed: With an MCL injury, protocols usually keep your knee moving straight ahead, with no sideways steps or twisting, until about week 6. After an MCL repair, protocols usually use partial weight with the brace locked straight for 1-2 weeks, then wean off by week 6. After an MCL repair, protocols usually limit bending to 90° in the first weeks, then progress it as tolerated. Your surgeon tells you when.
- Posterolateral corner repair: After posterolateral corner surgery, protocols usually avoid twisting on your leg and sideways strain on the knee for 6-8 weeks. Straighten your knee fully, but don't push it back past straight: protocols after posterolateral corner surgery avoid overstraightening. In the first 2 weeks, protocols usually keep your knee straight in the brace; bend it only as your physio or surgeon shows you. After posterolateral corner surgery, protocols usually allow no weight for 6 weeks, then partial weight to week 9, in a brace. Your surgeon sets yours. Weeks 2 to 6: protocols usually limit bending to about 90°, using a strap or your other leg, not your hamstrings. Your surgeon sets yours.
From the steps:
- Keep it gentle: it should never hurt, and don't press on a wound or stitches
Next in the programme
All exercises by levelThe 3D figure
The figures are Sports_Male_04 from the Microsoft Rocketbox Avatar Library, MIT licence. The poses are computed in the browser from the steps. Microsoft Rocketbox
MIT License
MIT License
Copyright (c) 2020 Microsoft
Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
